 |
Haier Hlp21n 6 6 Pound Pulsator Stainless
Only $259.95 @ Amazon
|
Haier Hlp21n 6 6 Pound Pulsator Stainless
I estimate that I have applied this washer for 4 loads each week since buying from J&R in early October, 2006. I live in a studio in New York and purchased this one because (1) it has a sink adapter, which the front-loading 14.3-lb model didn’t seem to include and (2) at 17.5 inches wide/deep, it fit through my bathroom door, which the front-loading 14.3-lb model (at 20.5 inches wide) wouldn’t.
Out of the box, you have to install an included metal pan at the bottom. Install it so that it is convex: there’s a reason that the legs are so high. One of the difficultnesses I had for the duration of installation was that one of the screws keeping this metal pan to the body comes very close to a clamp keeping the gooseneck drain tube as it exits the body. The clamp had fallen out of position, and the end of the screw is close to where the clamp goes. I don’t think I was ever in chance of puncturing the drainage tube, but it’s something to watch out for.
You need a place to hang the drainage tube, amid 31.5 and 40 inches high. The machine cannot fill the tub with water to a height above the maximum height of the drainage path.
On my introductory two loads, I made a puddle of water on the ground. There were two reasons for this: the primary time, the water supply hose was not tightened sufficiently at the machine end, and water dribbled out and behind the machine until I figured out what was going on. With that tightened arid employed a wrench), there was no leak. On my second load, I put in too a swell deal of clothes (more with regards to that later) and there was a water-resistant nylon jacket on top. Just before the very initial spun cycle, galore water was cupped on that jacket and did not drain out with the wash water. When the tub started to spin, that water came out. I never loaded that numerous clothes into the washer again, and haven’t had any spills since.
During a normal wash cycle, the machine does the following steps three times: fill, agitate, agitate, drain, spin, drain, spin, drain, spin. The second and third iterations are called the “rinse” cycle. Often, the water out of the drain is still bubbly after the second spin. (I use a quarter capful or less of All no-fragrance 3x fluid liquid So, I run another rinse cycle. whether or not the machine detects an unbalance condition for the duration of a spin, it will stop, fill the tub with water, and agitate in an undertake to redistribute the clothes before draining and spinning again. I think the machine does this two or three times before giving up and beeping ten times to alert the user of the unbalance condition.
During the agitation process, this machine tends to intertwine long or extended components of clothing — shirt sleeves and socks — into braid-like knots, which frequently trigger the unbalance condition during the subsequent spin. For example, when I wash four or five long-sleeved shirts together, I constantly have to untie and discerned two or three of the shirts where the sleeves have been twisted together. I think good washing is where the wash water might touch every surface of the clothes, and being tied together prevents this. These difficultnesses most likely would not happen with a front-loading washing machine.
What is the ability of this washer? Well, I would say:
2 bath towels; or
2 pairs of jeans or pants; or
2 sweatshirts and 1 pair of sweat pants; or
4 long-sleeved oxford shirts; or
6 small-size undershirts; or
8-12 medium-size boxer underwear.
That’s at the “high” water level. You might be capable to load more than that, but I think the clothes won’t get as clean, and the machine will in all probability reach more unbalance situations.
I once tried to wash a terrycloth robe. The robe fit in the tub, but the machine constantly got to an unbalance condition when it tried to spin. I think it’s sort of like trying to run a centrifuge with only one tube. on occasion after the spun cycle I find a sock or a shirt stretched all over the middle of the tub, instead of having been thrown centrifugally versus the tub walls.
Using my DSC-P71 digital camera in the multi-burst 30 frames-per-second mode and a light and a dark shirt in the washer, I estimate the firstborn spun at 450 rpm (light shirt passed once every 4 frames) and a final spun at 780 rpm (light shirt passed regarding 6.5 times in 0.5 seconds – when it comes to once every other frame). whether or not I hang the clothes in my studio (not in the bathroom), then they arid in regarding one day or less, depending on the humidity. It takes much longer whether or not I hang them in the bathroom.
Update (November 2007): This machine is still running. After a year, here are my comments:
After getting tired of the drain tube clamp falling out, I made two little wedges out of a folded-up credit card to hold the clamp in place.
I made a third spill (and this one was a huge huge once, the gooseneck drain hose came apart from the U-shaped drain-pipe hook. So, now I check that connection every week or so.
I constantly run an extra rinse cycle (or two). whether or not I have time, during the spun cycles, I lower the drain tube to concede more sudsy water to drain out. is a high-maintenance tactic, even though — it may lead to floods whether or not you’re not careful.) such a heap of types of clothes absorb and retain more water (and detergent) than others, and my skin is better after more of the detergent is rinsed out. You may take just-washed clothes from a popular washing machine and re-rinse them here to check how much detergent is left.
Update (April 2008): In the past two months, I have had two more major spills. Both times, it seems that the water-level sensor got stuck and failed to tell the inlet valve to shut off. When this happens, the water overflows the tub and comes out the bottom of the machine. you listen a click when the water level is reached, and then the valve shuts off; but in these cases, the original click never occurs.)
Now that I live in an apartment building with a good laundry room, I use this washer mostly for small items: socks, underwear, undershirts.
Update (April 2009): It turned out that the water-level sensor had failed. The sign of approaching failure is that the sensor will sometimes fail to close the valve when set to “high”, but will always close at “low” and “medium” water levels. Then, “medium” will stop working and the valve will only close when the water level is set to “low”. Since the manufacturer’s warranty had expired, I had the allocation substituted beneath my credit-card-based extended warranty program. Haier suggested two authorized mend operators; one of them said that they didn’t service this model. The other did, and charged $85 (diagnostic service call) plus $60 (labor) plus $21.52 portion The percentage had to be ordered and took regarding five weeks (!) to arrive.
No seriously, how have I been living in apartments for a decade without this machine? Through single and couple-dom life, I’ve been dragging my clothes to the local (and not-so local) laundromat resulting in frantic minutes scrounging for quarters, two hours of boredom, whites tardily turning yellow in those questionable large machines and a less-than-enthused meaningful other. Sometimes, I would just give up and wash those necessitated socks or undershirt in the shower praying they would arid hanged up overnight. It was one of those nights that I at last had had enough and the boy started scouring the internet for a solution.
This machine is *my* miracle of innovative engineering and has importantly bettered my life in quantifiable hours – and I bet has saved me cash in the long run (if you consider it’s five dollars per `big’ wash load at the laudromat, and they only have `big’ load machines.)
At in regards to 2 1/2 feet high and 17 inches wide, this machine effortlessly plugs into a three-pronged outlet, screws into a normal sink (normal screw-in adapter included – thank God!), and drainage hose hooks over the side of the sink, super easy. And it packs a powerful punch – everything comes out clean and astoundingly lint-free. I did have my doubts when it comes to the weird lint gatherer inside – which completely works, though a bit difficult to remove and empty. It’s in addition breathtakingly light – at 5’3″ I’m not incisively a brute force of strength, but I have no problem sliding the machine back into the corner without apparent effort once finished, although I would have a problem lifting it up entirely. It’s as well quiet, there’s only a slight audible hum when it vibrates – in regards to the same level as a person humming, which you may scarcely hear in the next room. It’s nowhere near as piercing as regular machines and doesn’t bothers anyone.
Any difficultnesses Well when we basi received, like others here we screwed in the bottom plate (there isn’t much installation, just the one plate) backwards – curving away from the ground and it did make a weird crunch sound while running – however, it’s a pretty tell-tale signal, and we flipped it around (like a cup sitting on a counter) in five minutes. Also, I was so excited regarding my original wash and over-loaded it – so we had a small puddle on the ground, but not since.
There are three water levels to choose from and at the high level it washes regarding two pants, a shirt, and three little items (say socks or underwear), or two towels and a facecloth, etc. I’ve easily fit in four t-shirts and five undergarments plus socks. By cautiously ensuring everything is equally distributed, I’ve even managed to wash my comforter cover – heaven! Realistically, it’s in regards to a half-load of laundry to a normal household washer. You control the water temperature by your sink. Being a girlie-girl when it comes to underwear, I may even throw in my delicates without worry. In two months I’ve had no problem with lace, silk, cotton or nylon ripping, and I haven’t even employed a mesh bag to protect them. Horray! The machine even allows for prolonged soaking if needed. Best of all, not one thing comes out dripping. The spin cycle on the machine thoroughly drains water so a heap of things arid overnight. After with regards to a half hour wash, everything is ready to hang.
Definitely now part of my *must have apartment appliances along with a microwave and toaster oven, I love this thing so much that I’ve actually named it Einstein and joked that must the significant other and I split up – the machine stays with me.
I’ve saved a lot of cash using this rather than paying the apartment usual wash food I would buy it again if nothing was better on the market, but there are a few cons that you must recognise about, and a few tips I’ll portion at the end of the review:
- You can’t in truth leave the apartment while running it is The water outflow hose may come loose and water may dump into your bathroom. See tips.
- You can’t run it at “high” water level. Leave it on “medium”. My best guess is that the water sensor works like a “brita” filter — it counts spins of a water-wheel to estimate the amount of water in the tub. This is not very precise and on the “high” setting, the tank will overflow and dump water on the floor.
- It often times requires intervention once during the wash cycle. It stops and reports an unbalanced load, which may start an endless fight to rebalance the wash. It’s not an overfill issue — it’s a pure remainder issue. This happens on 30% of my loads. See tips for trick to combat.
- Capacity is small. I went from doing 3 loads of mercantile washer to 5-6 loads in this unit. (I am now a total hang-dry convert — clothes last a lot longer than running in the drier, and saves money.)
- Haier aid is poor — I called because the inflow gasket leaked a bit, and they said it was requiring little effort to return the unit than to send me a new 50 cent gasket. Over time, the leak seems to have sealed itself.
Tips I can relay from using this washer for six months:
+ A lot of people install the bottom plate incorrectly. It is quiet if you install the bottom plate so that the bulge faces OUT toward the floor. This is non-intuitive and poorly documented, and the screw holes aren’t perfect.
+ Trick to prevent endless unbalances: When the washer comes unbalanced in spin cycle (50% of my loads), there is a trick to avoiding the endless re-rinse, re-spin cycle that can follow. You ought to turn off the water, turn off the machine, re-balance the laundry, turn on the machine, and force the machine into SPIN-ONLY by pressing the program button four times. This will save you a good amount of time.
+ Buy a cheap water flood detector for peace of mind. There is cheap cute one called a LeakFrog. Put this on the floor. Now, I can run the wash without worrying with regards to a flood. (This saved me once when outflow tube untied itself.)
+ Buy a “5 gallon paint strainer mesh” to collect lint and stay clear from drain clogs — rubber band it to the outflow. (These are a couple bucks at the hardware store and are ordinarily utilized to filter paint before going into a sprayer.) You will be surprised at the amount of lint that collects in these meshes. If you don’t have one of these, you may clog your tub drain, necessitating a service call. (This happened in my building.)
Sum-up: Not perfect, but I’d buy it again because of the money savings.
We have utilized the Haier Compact Washer virtually each and everyday for the past 8 months and have had no mechanical issues. Works swell on lightly soiled clothing and is highly recommended to any person with newborns or toddlers. Like the other reviews I advise you to double check all connections/fittings and make certain the drain hose is limited securely in the sink. Also, I will never wash more than 2-bath towels or 1-pair + 2-tshirts at a time. Otherwise the load will become unbalanced during the spin cycle.
Product Complaints:
- Handles on either side are exceedingly too small for moving the unit.
- Drain hose adapter will not fit over most general sinks. We have to use a heavy pot or pan to secure the hose in the sink.
Other than that we are very pleased with our purchase.
Why didn’t I buy this sooner?? This washer spins so well that even towels I wash in the evening are dry before I go to bed (I hang them and have a fan on them). The washer holds plenty and runs fantastically quietly. Loads that do retain more water after draining–towels/sweaters–do tend to make the first spin cycle a little piercing loud hum sound). However, the initial spin is less than 10 seconds, so with regards to the time I detect that the washer is making more sound than normal, it’s over.
Some the reviews mentioning placing the bottom tray ‘convex/concave’ were confusing to me. They may be clear to others, but I wasn’t certain what the convex/concave was in reference to (me as I’m installing the tray with the washer on it is side, or in reference to the washer when it’s upright??), so here’s what worked for me: install the tray so that it sets like it will have to catch water (like the drip pan beneath your refrigerator) when the washer is upright. Of course, with the holes in it, it isn’t genuinely a drip-pan, but hopefully this is easier to comprehends
I found the ‘quick connect’ thing that was included with my washer retained leaking at the sink connection (I really had to make the connection at the washer tight to stop leaks there). I went to Home Depot and got a new connector for the sink for eight bucks & haven’t had a problem since. I as well tied both the hose & drain hoses together with velcro ties so they hang together in the sink. When I’m not using the hoses, I then use the velcro ties to hang the hoses on a hook on the wall.
I do love my Downy ball, but I think it makes alot of noise in this washer as it floats & rubs versus the steel washer basin, so I just add the softener directly to the final rinse (there are 2 rinse cycles).
As another reviewer said— the lint filter is incredible. I didn’t think that little thing would catch much, but I really do have to empty it after every 1-3 washes.
If you’re doing your laundry at a laundromat, save your money and time. This little washer is fantastic. I’m a laundry freak—I love doing laundry and I’m very picky with regards to where/how it’s done. Not to mention the safety concern in public laundromats. This washer is worth its weight in gold. Really.
I had the littler version for 2 1/2 years and after much abuse it at long last halted spinning (… and I mean ABUSE)! It halted spinning after I shoved a comforter into it (yes – I will have to have known better). And that one I purchased for $145 delivered. all the old one needed was a new belt! So my best friend will be getting a few years of service out of it as well!).
This time around I decisive to get the more spectacular model and how happy am I had it in my house and doing wash 1 1/2 days after ordering (and that was with normal shipping).
I don’t have (and did not with the other one) any of the issues others have seen with leaking etc. First of all, I read directions…. There is some small assembly. pays attention and make certain everything is tight and you wont have issues.
DO NOT USE NORMAL DETERGENT….. BUY HE only and you’ll be fine.
As with my previous one, I am happy as a clam. Cannot to this day, 2 1/2 years after buying my one, perceive why I put up with laundry mats for so long.
If I hadn’t overstuffed the old one (time after time after time), I am certain it would still be working today….. And I dont mind, I was spending $100 a month at the laundry mat, so it paid for itself in six weeks.
This one I got for $245 delivered, so it will remunerate for itself in 10 weeks. I can live with that.
Go for it is You really have nothing to lose and if you are spending 80-100 bucks a month at the laundry mat, you would still make out even if the thing broke after 2-3 months.
Makes sense to me.
OH – A QUICK TIP FOR THE DRAIN HOSE – I tie it to the water intake hose… thence it is always in the sink and I never have to worry in regards to it coming loose… I tie them together in regards to 5-7 inches from the end. Then the end of the water intake hose goes to the faucet, and by default the end of the drain hose sits in the sink tied to it <grin>
For other outstanding information – clcik SEE ALL REVIEWs from me (there’s only one) and its for the other model, on there I have picutres and part numbers for connecting to a bathroom sink (and it all applies to this model as well)…. as a matter of fact, the wheels I purchased for the first one, fits this one without any adjustments at all.
I’m so happy to have found this great little washer! It cleans and spins dry just as well as the huge ones, but takes up very little space. It certain beats lugging my clothes to the laundromat, and I don’t even mind hanging them up to dry. I in addition employed a Downey ball for the fabric softener.
The only problem I had was with attaching the bottom plate. The screws don’t line up exactly and they don’t screw in all the way. As long as you can put most of them in, in will be fine. Also, it ought to be mounted so that the concave area points toward the floor so that the inside mechanisms don’t hit it is This will stay clear from the jack hammer sounds that other reviewers have experienced. Actually, I find this machine to be very quiet.
I hook mine up to my bathroom sink, but the gooseneck that is supplied is too small to fit over my sink. I solved that problem by using a Velcro tie to attach the drain hose to the supply hose and it works perfectly.
To keep away from leaks, make sure the hoses are screwed on tightly, don’t overload the machine, and don’t use too much detergent. I used a small amount of Method detergent, which is low sudsing. I highly recommend this cute little machine!
We bought this washer a couple of weeks ago and as soon we turned it on, the washer started making a screeching noise in the wash cycle. I called Customer assist immediately, but they assumed it was a defective piece without even trying to find out more details.
There is utterly no onsite aid or phone support to help you troubleshoot. We had to cut the power chord, remove the original sticker from the machine and mail it back along with the sales receipt. Shiiping is not covered underneath warranty, so we had to pay for shipping again. Haier shipped another unit after 3 weeks. We obtained a new unit and when we switched it on, it started making the same accurate noise. This time we didn’t want to call Customer support as they were least helpful.
We tried a couple of things..
First, we checked on the capacity, this machine takes very few clothes. We started with a small load of our baby clothes and the washer started working.
Secondly, the bottom panel needs to be limited outwards. When the washer is loaded with water, it sinks a bit and it hits the bottom panel when fixed inwards.
If you experience alike difficulties, Please take these two precautions before you go through the hassle of sending it back and getting a new washer shipped again.
I have had my Haier HLP21E for regarding a week now…I got it online for when it comes to $240 (including shipping).
The installation was a little bit tricky due to the akward diagrams on the manual. Luckily they have a 24 hour technical support 800 #.
The first time I ran the machine it leaked a tiny bit…but that stopped by itself the next day. I have used the machine for with regards to 6 days in a row and it seems to work perfectly now.
There are a few quirks with the machine. The water temperature is controlled by the hot/cold handles on the sink. The washer needs to be reasonably close to the faucet and sink because the hoses are not that long. I also have to use the handle of a heavy beer mug in order to weigh down the drain hose in the sink. Unless you have a dryer, the clothes need to be hung up to dry (I dry them on my shower curtain rod and most stuff dries overnight).
The good part when it comes to the washer is that my clothes come out clean and smelling great. I no longer have to haul all my laundry downstairs to the laundromat across the street. I’m also saving 3 bucks a load, which is what I used to pay at the laundromat.
So far I really like this little machine! I think it may end up being the best buy I’ve made in a long time.
Absolutly everything I expected. The Haier HLP21E, 6 3/5 lb. capacity, holds in regards to 1/2 load of a regular sized drum. Washes wonderful and spins out to just damp. I’ve been using Arm & Hammer liquid with the softener in it and have had no over-sudsing issues. ( I use when it comes to 1/2-3/4 capful). It came in with regards to 5 days, much earlier than the esimated shipping date. It hooked up easy and has no leaks, and doesn’t play Jingle Bells, (LOL) like previous models! It’s perfect for 1-2 people in a small apartment, probably not the most paractical for a big family, but I love it is I think I was getting depression from having to drag my laundry out and up and down my stairs to the 2nd floor, exceptionally during WNY winter, and now I’m SAVED!!!
No, I don’t have a dryer, but I have use of a clothes line and bought a dryer rack that fits in my bath tub. So, Love, Love, Love!! And I make everybody that comes over, check-it-out, and they love it too! 
Oh, and I’m going to put it on a wheeled plant stand too, (like I read that an individual else did) as soon as I find one with locking wheels.
Thanks for reading,
L.E.
Western NY